The resistor adds around 15 watts extra draw over the LED draw, the LED light use around 6 watts + 15 = 21 watts total. To compare, an 1156 bulb uses around 26 watts, 1157 23 watts, and 715508 18 watts.
The resistor is needed for existing flasher relays to work with the LED lights. In some cases, the draw can be too high, it does not happen often and if it happens you can cut one side of the wire going to the resistor, and cover the wire end with some silicone to avoid shorting to ground.
If you replace your stock flashers with LED flashers, you might need a new flasher relay or a set of resistors in order for the flashers to flash normally.
If you replace your stock flashers with LED flashers, you might need a set of resistors or a LED flasher relay in order for the flashers to flash normally. If possible use the LED flasher relay instead of the resistors. Find it further down on this page.
LED-486, Round stud mounted warning light for mounting onto fenders, and many other places where you need an amber warning light. 8.5 watt. Note - This light does not have a built-in flasher, they would require a flasher relay in order to flash, or installed in place of an existing flasher. Also - most older flasher relays will not work with this low-wattage turn signal, you will need flasher relay SKU LL0466 for the turn signal to work.
LED-2206 w/ built in resistor. Used on CaseIh, IH, FNH, Versatile/Buhler and more. Replaces OEM Part Numbers: 92185C1, 216044C91, 216044C92, 92260C1, 130882C91, 107324C91, V93104, V77050, 9706415, 86014019, 86023276, 86016518, 86012669, 87053368, 83977683, & 8770630.
LED-2417 amber with a built-in resistor. No need for special LED flasher relays! This model fits some CIH models - replaces OEM # 84269970, 84273385, 84273384
Set of 2 amber lights (right and left) for JD, NH, and more. Now with a built-in resistor for an easy install. OEM Part NH 86507530, JD RE39582, RE39581, RE39582, CIH 1983404C1.
Amber LED Light for direct replacement, Plug & Play. Light will bolt right into factory light housing. Set of right and left amber light. The light has a built-in resistor to work with the original factory flasher. Replaces Case/IH Part Number: 279223A1 + 279224A1
LED-547 White with amber flasher - set of 2 - right and left side. LED Light for direct replacement, Plug & Play. Light will bolt right into factory light housing. This light is the front corner amber light with an attached white work light. The amber light has a built-in resistor to work with the original factory flasher. Replaces Case/IH Part Number: 279219A1 & 279220A1. Right and left light included.
LED-601 White with red light - set of 2 - right and left side. Light will bolt right into factory light housing. This light is the corner fender red light with an attached white work light. Right and left light are included. Replaces Case/IH Part Number: 279221A1 & 279222A1. This light only has the white work light and red tail light, there is no brake light wire - it was made wrong from the factory, so it is sold as is and cheap.
LED-601 White with red light - set of 2 - right and left side. Light will bolt right into factory light housing. This light is the corner fender red light with an attached white work light. Right and left light are included. Now made with tail light and stop light. Note: Red light will require splicing. Replaces Case/IH Part Number: 279221A1 & 279222A1.
LED-603 Amber with red light - set of 2 - right and left side. The light will bolt right into the factory light housing. This light is the corner
fender amber flasher with an attached red light. The amber light has a built-in resistor to work with the original factory flasher. Replaces Case/IH Part Number: 357540A1 & 357541A1. Right and left lights are included. This light only has tail and turn light, there is no brake light wire - it was made wrong from the factory, so it is sold as is and cheap.
LED-603 Amber with red light - set of 2 - right and left side. The light will bolt right into the factory light housing. This light is the corner
fender amber flasher with an attached red light. The amber light has a built-in resistor to work with the original factory flasher. Replaces Case/IH Part Number: 357540A1 & 357541A1. Right and left lights are included. Now made with tail light and stop light. Note: Red light will require splicing.
LED 2x5 LED light for the top front cab on the 7000-8000 series tractor, and front hood light on older JD’s, 55 and 60 series. 50° beam pattern. 1700 effective lumen.
PAR-36 size replacement LED light, this model has a lens that looks like the halogen lights, makes it appear as OEM. 60° Flood Beam. 1400 lumen, 30 watt rated / 18 watt use.
Cable for connecting the Thomas HP and the LED-765 Oval / 760 Rectangular to tractors and combines that previously used a weather pack 2 pin connector.
LED-760 is a 4x6 style LED work light. 6 x Osram P9 LED's at 10 watt each, 4800 effective lumens, 5200-5500k, and only 3.8 amp/46 watt use. Select the light beam type, then select the bracket you need for your application. Includes a 5" adapter cable that fits 9005 or H11 connectors. You can find more adapter cables at the bottom or right side of this page. This is an updated model of our LED-660.
Cable for connecting the Thomas HP and the LED-760/765 lights to tractors and combines that previously used a 9005 bulb. Newer JD (20, 30, and R series and S series combines + other brands where the light replaced used a 9005 bulb.
24 Watt Oval LED work light. Now includes H11 connector (same as 880 series bulb connector) so the light will plug and play on most tractors and combines using the same size light.
LED-765 is a 4x6 style Oval LED work light. 6 x Osram P9 LED's at 10 watt each, 4800 effective lumens, 5000-5500k, and only 3.8 amp/46 watt use. Select the light beam type, then select the bracket you need for your application. Includes a 5" adapter cable that fits 9005 or H11 connectors. You can find more adapter cables at the bottom or right side of this page. This is an updated model of our LED-665.
LED-760 is a 4x6 style LED work light. 6 x Osram P9 LED's at 10 watt each, 4800 effective lumens, 5200-5500k, and only 3.8 amp/46 watt use. Select the light beam type, then select the bracket you need for your application. Includes a 5" adapter cable that fits 9005 or H11 connectors. You can find more adapter cables at the bottom or right side of this page. This is an updated model of our LED-660.
HD Wi-Fi Camera for Ipad / Android. For use with 12 volt DC power supply or 12 volt battery. Very easy to use. App name "JoyTrip". NOTE - might not work with Samsung phones.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700. 40° beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700. 60° Flood Beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700 Hi-Lo Beam, 800 low beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
LED 2x5 LED light for the top front cab on the 7000-8000 series tractor, and front hood light on older JD’s, 55 and 60 series. 50° beam pattern. 1700 effective lumen.
Cab lights for the 9000 series JD combine using a rectangular light on the cab - fits any vehicle using the JD9000 series cab. Use the combo beam for most distance, we suggest 2 combo beam and 4 flood beam for the combines.